更改xilinx EDK 14.4中的MHS文件，在uart外围设备中添加端口

Question

我正在尝试在由xilinx-EDK创建的uart中添加一个端口(在我的硬件设置的EDK中进行硬件设计)，我知道通过更改MHS文件我可以添加一个端口。但是，每当我更改MHS文件时，它都会显示一个错误，我无法添加端口，因为它不在MPD文件中，并且项目在xilinx EDK中关闭。

我的设置:我有xc6slx9 2 csg324 fpga。我有rs232通用异步收发器，它有三个端口RX，TX，SW。但是Xilinx创建的默认设计在EDk上只有TX和RX端口，所以我需要添加SW端口。我正在写MHS文件。

# ##############################################################################
# Created by Base System Builder Wizard for Xilinx EDK 14.4 Build EDK_P.49d
# Mon Mar 03 09:02:22 2014
# Target Board:  Custom
# Family:    spartan6
# Device:    xc6slx9
# Package:   csg324
# Speed Grade:  -2
# ##############################################################################
 PARAMETER VERSION = 2.1.0


 PORT RS232_Uart_1_sout = RS232_Uart_1_sout, DIR = O
 PORT RS232_Uart_1_sin = RS232_Uart_1_sin, DIR = I
 PORT RESET = RESET, DIR = I, SIGIS = RST, RST_POLARITY = 1
# PORT CLK_P = CLK, DIR = I, DIFFERENTIAL_POLARITY = P, SIGIS = CLK, CLK_FREQ = 100000000
# PORT CLK_N = CLK, DIR = I, DIFFERENTIAL_POLARITY = N, SIGIS = CLK, CLK_FREQ = 100000000
 PORT CLK = CLK, DIR = I, SIGIS = CLK, CLK_FREQ = 27000000
 PORT TX_enable = TX_enable, DIR = O   # I am trying to add this port 


BEGIN proc_sys_reset
 PARAMETER INSTANCE = proc_sys_reset_0
 PARAMETER HW_VER = 3.00.a
 PARAMETER C_EXT_RESET_HIGH = 1
 PORT MB_Debug_Sys_Rst = proc_sys_reset_0_MB_Debug_Sys_Rst
 PORT Dcm_locked = proc_sys_reset_0_Dcm_locked
 PORT MB_Reset = proc_sys_reset_0_MB_Reset
 PORT Slowest_sync_clk = clk_100_0000MHz
 PORT Interconnect_aresetn = proc_sys_reset_0_Interconnect_aresetn
 PORT Ext_Reset_In = RESET
 PORT BUS_STRUCT_RESET = proc_sys_reset_0_BUS_STRUCT_RESET
END

BEGIN lmb_v10
 PARAMETER INSTANCE = microblaze_0_ilmb
 PARAMETER HW_VER = 2.00.b
 PORT SYS_RST = proc_sys_reset_0_BUS_STRUCT_RESET
 PORT LMB_CLK = clk_100_0000MHz
END

BEGIN lmb_bram_if_cntlr
 PARAMETER INSTANCE = microblaze_0_i_bram_ctrl
 PARAMETER HW_VER = 3.10.c
 PARAMETER C_BASEADDR = 0x00000000
 PARAMETER C_HIGHADDR = 0x00003fff
 BUS_INTERFACE SLMB = microblaze_0_ilmb
 BUS_INTERFACE BRAM_PORT = microblaze_0_i_bram_ctrl_2_microblaze_0_bram_block
END

BEGIN lmb_v10
 PARAMETER INSTANCE = microblaze_0_dlmb
 PARAMETER HW_VER = 2.00.b
 PORT SYS_RST = proc_sys_reset_0_BUS_STRUCT_RESET
 PORT LMB_CLK = clk_100_0000MHz
END

BEGIN lmb_bram_if_cntlr
 PARAMETER INSTANCE = microblaze_0_d_bram_ctrl
 PARAMETER HW_VER = 3.10.c
 PARAMETER C_BASEADDR = 0x00000000
 PARAMETER C_HIGHADDR = 0x00003fff
 BUS_INTERFACE SLMB = microblaze_0_dlmb
 BUS_INTERFACE BRAM_PORT = microblaze_0_d_bram_ctrl_2_microblaze_0_bram_block
END

BEGIN bram_block
 PARAMETER INSTANCE = microblaze_0_bram_block
 PARAMETER HW_VER = 1.00.a
 BUS_INTERFACE PORTA = microblaze_0_i_bram_ctrl_2_microblaze_0_bram_block
 BUS_INTERFACE PORTB = microblaze_0_d_bram_ctrl_2_microblaze_0_bram_block
END

BEGIN microblaze
 PARAMETER INSTANCE = microblaze_0
 PARAMETER HW_VER = 8.40.b
 PARAMETER C_INTERCONNECT = 2
 PARAMETER C_USE_BARREL = 1
 PARAMETER C_USE_FPU = 0
 PARAMETER C_DEBUG_ENABLED = 1
 PARAMETER C_ICACHE_BASEADDR = 0X00000000
 PARAMETER C_ICACHE_HIGHADDR = 0X3FFFFFFF
 PARAMETER C_USE_ICACHE = 0
 PARAMETER C_ICACHE_ALWAYS_USED = 0
 PARAMETER C_DCACHE_BASEADDR = 0X00000000
 PARAMETER C_DCACHE_HIGHADDR = 0X3FFFFFFF
 PARAMETER C_USE_DCACHE = 0
 PARAMETER C_DCACHE_ALWAYS_USED = 0
 BUS_INTERFACE ILMB = microblaze_0_ilmb
 BUS_INTERFACE DLMB = microblaze_0_dlmb
 BUS_INTERFACE M_AXI_DP = axi4lite_0
 BUS_INTERFACE DEBUG = microblaze_0_debug
 PORT MB_RESET = proc_sys_reset_0_MB_Reset
 PORT CLK = clk_100_0000MHz
END

BEGIN mdm
 PARAMETER INSTANCE = debug_module
 PARAMETER HW_VER = 2.10.a
 PARAMETER C_INTERCONNECT = 2
 PARAMETER C_USE_UART = 1
 PARAMETER C_BASEADDR = 0x41400000
 PARAMETER C_HIGHADDR = 0x4140ffff
 BUS_INTERFACE S_AXI = axi4lite_0
 BUS_INTERFACE MBDEBUG_0 = microblaze_0_debug
 PORT Debug_SYS_Rst = proc_sys_reset_0_MB_Debug_Sys_Rst
 PORT S_AXI_ACLK = clk_100_0000MHz
END

BEGIN clock_generator
 PARAMETER INSTANCE = clock_generator_0
 PARAMETER HW_VER = 4.03.a
 PARAMETER C_CLKIN_FREQ = 27000000
 PARAMETER C_CLKOUT0_FREQ = 1687500
 PARAMETER C_CLKOUT0_GROUP = NONE
 PORT LOCKED = proc_sys_reset_0_Dcm_locked
 PORT CLKOUT0 = clk_100_0000MHz
 PORT RST = RESET
 PORT CLKIN = CLK
END

BEGIN axi_interconnect
 PARAMETER INSTANCE = axi4lite_0
 PARAMETER HW_VER = 1.06.a
 PARAMETER C_INTERCONNECT_CONNECTIVITY_MODE = 0
 PORT interconnect_aclk = clk_100_0000MHz
 PORT INTERCONNECT_ARESETN = proc_sys_reset_0_Interconnect_aresetn
END

BEGIN axi_uartlite
 PARAMETER INSTANCE = RS232
 PARAMETER HW_VER = 1.02.a
 PARAMETER C_BAUDRATE = 9600
 PARAMETER C_DATA_BITS = 8
 PARAMETER C_USE_PARITY = 0
 PARAMETER C_ODD_PARITY = 1
 PARAMETER C_BASEADDR = 0x40600000
 PARAMETER C_HIGHADDR = 0x4060ffff
 BUS_INTERFACE S_AXI = axi4lite_0
 PORT S_AXI_ACLK = clk_100_0000MHz
 PORT TX = RS232_Uart_1_sout
 PORT RX = RS232_Uart_1_sin
 PORT TX_enable = RS232_TX_enable # I am trying to add this port 
END

/

很容易添加一个没有连接到任何ipcore的端口。只需使用以下几行：

PORT TX_enable = net_vcc, DIR = O 

Answer 1

不能将端口添加到MHS文件中的pcore (例如axi_uartlite)。

pcore上的端口由该核心的MPD文件定义。对于Xilinx pcore，可以在以下位置找到MPD文件：

[Xilinx_Install_Dir]\ISE_DS\EDK\hw\XilinxProcessorIPLib\pcores\

如果查看axi_uartlite的MPD文件，就会发现TX_ENABLE不是可用的端口。