让Killer Wireless-AC 1535安装Ubuntu 16.04

Question

我的无线设备是168c:003e:1a56:1353 rev 32。安装程序包含一个4.4.0-21-lowlatency内核，我在/lib/firmware/ath10k/QCA6174/hw3.0中看到了固件文件-- board.bin和firmware-4.bin。这些是股票文件。在dmesg中，我看到初始化失败，这是事实，我甚至没有在ifconfig中看到一个设备。在初始化过程中，它正在寻找一个不存在的firmware-5.bin。

首先，我尝试添加固件-5.bin在这里烹饪：https://github.com/kvalo/ath10k-firmware/pull/4/files

这没什么用，文件里的魔法不匹配。我想它已经煮了4.2或什么的了。然后，我尝试使用official repo https://github.com/kvalo/ath10k-firmware/tree/master/QCA6174/hw3.0 (http://www.killernetworking.com/support/knowledge-base/17-linux/20-killer-wireless-ac-in-linux-ubuntu-debian推荐的)中的所有文件。魔法不匹配。

由于我是在安装的开始，重新启动对我来说不是一个选项，这是一个22捕获。相反，我写了一个小剧本，modprobe -rs ath10k_pci，ath10k_core，ath，mac80211和cfg80211。另一个脚本insmods，这些都是相反的顺序。

我也尝试了板-2.bin由https://github.com/kvalo/ath10k-firmware/pull/3。魔法不匹配。

更多的信息。安装程序的/lib/firmware/ath10k/QCA6174/hw3.0固件目录的初始/原始状态：

-rw-r--r-- 1 root root   8124 Mar 21 12:27 board.bin
-rw-r--r-- 1 root root 733784 Mar 21 12:27 firmware-4.bin

cb37c63d9ca28f53fea1ff09ad7c7a82  board.bin
a5dfbc03c9a7a73f7aa8d0a94a6d9426  firmware-4.bin

这导致：

[  118.170694] ath10k_pci 0000:04:00.0: enabling device (0000 -> 0002)
[  118.171818] ath10k_pci 0000:04:00.0: pci irq msi-x interrupts 8 irq_mode 0 reset_mode 0
[  118.658737] ath10k_pci 0000:04:00.0: Direct firmware load for ath10k/cal-pci-0000:04:00.0.bin failed with error -2
[  118.658754] ath10k_pci 0000:04:00.0: Direct firmware load for ath10k/QCA6174/hw3.0/firmware-5.bin failed with error -2
[  118.658770] ath10k_pci 0000:04:00.0: could not fetch firmware file 'ath10k/QCA6174/hw3.0/firmware-5.bin': -2
...
[  128.810919] ath10k_pci 0000:04:00.0: Direct firmware load for ath10k/QCA6174/hw3.0/board-2.bin failed with error -2
[  131.928674] ath10k_pci 0000:04:00.0: qca6174 hw3.2 (0x05030000, 0x00340aff sub 1a56:1535) fw WLAN.RM.2.0-00180-QCARMSWPZ-1 fwapi 4 bdapi 1 htt-ver 3.26 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1 features wowlan,ignore-otp,no-4addr-pad
[  131.928676] ath10k_pci 0000:04:00.0: debug 0 debugfs 1 tracing 1 dfs 0 testmode 0
[  134.928910] ath10k_pci 0000:04:00.0: could not suspend target (-11)
[  134.982552] ath: EEPROM regdomain: 0x6c
[  134.982553] ath: EEPROM indicates we should expect a direct regpair map
[  134.982554] ath: Country alpha2 being used: 00
[  134.982555] ath: Regpair used: 0x6c
[  136.139717] ath10k_pci 0000:04:00.0 wlp4s0: renamed from wlan0
[  147.251066] IPv6: ADDRCONF(NETDEV_UP): wlp4s0: link is not ready
[  152.475059] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11
[  158.475164] ath10k_pci 0000:04:00.0: could not suspend target (-11)
[  158.532546] IPv6: ADDRCONF(NETDEV_UP): enp6s0: link is not ready
[  158.533313] IPv6: ADDRCONF(NETDEV_UP): enp6s0: link is not ready
[  167.547281] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11
[  173.547366] ath10k_pci 0000:04:00.0: could not suspend target (-11)
[  178.826678] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11
[  184.826637] ath10k_pci 0000:04:00.0: could not suspend target (-11)
[  202.258851] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11
[  208.258910] ath10k_pci 0000:04:00.0: could not suspend target (-11)
[  213.537200] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11
[  219.537070] ath10k_pci 0000:04:00.0: could not suspend target (-11)
[  235.258295] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11
[  241.258474] ath10k_pci 0000:04:00.0: could not suspend target (-11)
[  246.537511] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11
[  252.537681] ath10k_pci 0000:04:00.0: could not suspend target (-11)
[  268.259942] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11
[  274.259976] ath10k_pci 0000:04:00.0: could not suspend target (-11)
[  279.538073] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11
[  285.538232] ath10k_pci 0000:04:00.0: could not suspend target (-11)
[  301.260390] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11
[  307.260552] ath10k_pci 0000:04:00.0: could not suspend target (-11)
[  312.538796] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11
[  318.539935] ath10k_pci 0000:04:00.0: could not suspend target (-11)
...
[  340.262113] ath10k_pci 0000:04:00.0: could not suspend target (-11)
[  345.540330] ath10k_pci 0000:04:00.0: failed to enable dynamic BW: -11
[  351.540341] ath10k_pci 0000:04:00.0: could not suspend target (-11)

我的一次尝试在没有固件崩溃的情况下，在dmesg看来是很有希望的，但无法插入核心：

-rw-r--r-- 1 root root  42110 Jul  3 09:56 board-2.bin
-rw-r--r-- 1 root root   8124 Jul  3 09:56 board.bin
-rw-r--r-- 1 root root 733784 Mar 21 12:27 firmware-4.bin
-rw-r--r-- 1 root root 572324 Jul  3 09:57 firmware-5.bin

5e47d7cbe6255e4ac3ef71f6e2210f95  board-2.bin
1d07f60b4f6e3dc06028f4f31d1eec60  board.bin
a5dfbc03c9a7a73f7aa8d0a94a6d9426  firmware-4.bin
2c5629dc360ee3606c12088ee5e2de98  firmware-5.bin 

[ 2798.276194] ath10k_pci 0000:04:00.0: pci irq msi-x interrupts 8 irq_mode 0 reset_mode 0
[ 2798.477454] ath10k_pci 0000:04:00.0: Direct firmware load for ath10k/cal-pci-0000:04:00.0.bin failed with error -2
[ 2798.539215] ath10k_pci 0000:04:00.0: found invalid board magic
[ 2798.622537] ath10k_pci 0000:04:00.0: otp calibration failed: 3
[ 2798.622538] ath10k_pci 0000:04:00.0: failed to run otp: -22
[ 2798.622539] ath10k_pci 0000:04:00.0: could not init core (-22)
[ 2798.622550] ath10k_pci 0000:04:00.0: could not probe fw (-22)
[ 3318.953548] IPv6: ADDRCONF(NETDEV_UP): enp6s0: link is not ready
[ 3318.954150] IPv6: ADDRCONF(NETDEV_UP): enp6s0: link is not ready 

大多数情况下，我会在dmesg中看到固件崩溃。我很快就会试一下deb包。

注意:每次启动时检查BIOS没有从UEFI模式恢复到UEFI非常重要。显然，这是至关重要的安装，没有CSM安装只是静默暂停。还要检查BIOS是否没有恢复到安全启动模式。多头痛啊！

将v1.157固件包升级到1.158有帮助(我不需要交换1.158 deb中的任何文件)。详细信息：

1. 首先，我停止了网络: sudo su /etc/init.d/Networking /etc/init.d/Networking
2. 卸载内核模块:mod探针-r ath10k_pci -r -r ath10k_core -r -r ath mod探头-r mac80211 mod探头-r cfg80211
3. 升级了固件包dpkg -i linux-固件_1.158_all.deb

之后，固件目录的内容：

-rw-r--r-- 1 root root 271412 May  6 12:42 board-2.bin
-rw-r--r-- 1 root root   8124 Apr 25 12:59 board.bin
-rw-r--r-- 1 root root 733784 Apr 25 12:59 firmware-4.bin

ac5184615090503870442da5f703de25  /lib/firmware/ath10k/QCA6174/hw3.0/board-2.bin
cb37c63d9ca28f53fea1ff09ad7c7a82  /lib/firmware/ath10k/QCA6174/hw3.0/board.bin
a5dfbc03c9a7a73f7aa8d0a94a6d9426  /lib/firmware/ath10k/QCA6174/hw3.0/firmware-4.bin 

dmesg：

[ 1084.393020] ath10k_pci 0000:04:00.0: pci irq msi-x interrupts 8 irq_mode 0 reset_mode 0
[ 1084.594123] ath10k_pci 0000:04:00.0: Direct firmware load for ath10k/cal-pci-0000:04:00.0.bin failed with error -2
[ 1084.594143] ath10k_pci 0000:04:00.0: Direct firmware load for ath10k/QCA6174/hw3.0/firmware-5.bin failed with error -2
[ 1084.594149] ath10k_pci 0000:04:00.0: could not fetch firmware file 'ath10k/QCA6174/hw3.0/firmware-5.bin': -2
[ 1086.774542] ath10k_pci 0000:04:00.0: qca6174 hw3.2 (0x05030000, 0x00340aff sub 1a56:1535) fw WLAN.RM.2.0-00180-QCARMSWPZ-1 fwapi 4 bdapi 2 htt-ver 3.26 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1 features wowlan,ignore-otp,no-4addr-pad
[ 1086.774545] ath10k_pci 0000:04:00.0: debug 0 debugfs 1 tracing 1 dfs 0 testmode 0
[ 1086.828603] ath: EEPROM regdomain: 0x6c
[ 1086.828605] ath: EEPROM indicates we should expect a direct regpair map
[ 1086.828606] ath: Country alpha2 being used: 00
[ 1086.828607] ath: Regpair used: 0x6c
[ 1086.830651] ath10k_pci 0000:04:00.0 wlp4s0: renamed from wlan0 

所以我们终于有了wlan0 (改名为wlp4s0)

1. 加载内核模块cd /lib/模块/4.4.0-21-低延迟/内核/ insmod网/无线/cfg80211.ko/mac80211/mac80211.ko insmod驱动程序/net/wireless/ath/ath.ko insmod驱动程序/net/wireless/ath/ath10k/ath10k_pci.ko
2. 开始联网/etc/init.d/联网开始/etc/init.d/网络管理器启动
3. 需要重新启动nm-applet：kilall -applet&

现在我可以安装mdadm了。如果我完成我的下一个任务目标，我将最终能够安装Linux：如何在安装过程中确定NMVe SSD的设备名称

只是FYI，当前Ubuntu 17.04的状态是(错误，错误，错误.)：

[    2.772902] ath10k_pci 0000:05:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:05:00.0.bin failed with error -2
[    2.772909] ath10k_pci 0000:05:00.0: Direct firmware load for ath10k/cal-pci-0000:05:00.0.bin failed with error -2
[    2.773036] ath10k_pci 0000:05:00.0: Direct firmware load for ath10k/QCA6174/hw3.0/firmware-5.bin failed with error -2
[    2.773038] ath10k_pci 0000:05:00.0: could not fetch firmware file 'ath10k/QCA6174/hw3.0/firmware-5.bin': -2
[    2.773892] ath10k_pci 0000:05:00.0: qca6174 hw3.2 target 0x05030000 chip_id 0x00340aff sub 1a56:1535
[    2.773893] ath10k_pci 0000:05:00.0: kconfig debug 0 debugfs 1 tracing 1 dfs 0 testmode 0
[    2.774309] ath10k_pci 0000:05:00.0: firmware ver WLAN.RM.2.0-00180-QCARMSWPZ-1 api 4 features wowlan,ignore-otp,no-4addr-pad crc32 75dee6c5

linux-firmware包v1.164.1

https://giphy.com/gifs/justin-monkey-i-am-disappointed-l3vRhaxVcQ1i0CZlC

Answer 1

请试用较新的固件包。使用互联网连接后，请打开终端并执行以下操作：

wget http://mirrors.kernel.org/ubuntu/pool/main/l/linux-firmware/linux-firmware_1.161.1_all.deb
sudo dpkg -i linux-firmware*.deb
sudo modprobe -r ath10k_pci && sudo modprobe ath10k_pci

你的无线电现在应该能工作了。