blocks|key|734835|text|您将无法通过ESXi完成这一任务--它不支持可以执行此类任务的第三方应用程序。至少，您必须启用iLO，并通过最初在机器上物理地这样做给它一个ip地址。|type|unstyled|depth|inlineStyleRanges|entityRanges|data|734836|ESXi了解IPMI，并支持通过WBEM进行远程管理，WBEM可以与嵌入式硬件管理组件(BMC\iLO等)进行通信，因此可能可以通过类似HP之类的方法来实现这一点，但我从未见过这样的例子。|entityMap^0|0^^$0|@$1|2|3|4|5|6|7|E|8|@]|9|@]|A|$]]|$1|B|3|C|5|6|7|F|8|@]|9|@]|A|$]]]|D|$]]

You're not going to be able to do this via ESXi - it doesn't support third party applications that can do this type of thing. At a minimum you will have to enable iLO and give it an ip-address by physically doing so at the machine initially. 

ESXi is IPMI aware and does support remote management via WBEM which can talk to the embedded hardware management components (BMC\iLO etc) so it may be possible to do this via something like HP SIM but I've never seen an example.

blocks|key|3021794|text|如果这是一次过的工作，我会尝试让一个人在现场设置它在本地(惠普恢复设置时，他们交换了部分？他们总是为我们服务)。然后，我将在一个非常小的linux可引导ISO上工作，安装了linux版本的hponcfg，这样您就可以启动它并做您想做的事。|type|unstyled|depth|inlineStyleRanges|entityRanges|data|entityMap^0^^$0|@$1|2|3|4|5|6|7|C|8|@]|9|@]|A|$]]]|B|$]]

If it's a one-off job I'd try to get someone on-site to set it up locally (didn't HP reinstate settings when they swapped out the part? they always do for us). I'd then work on a very small linux bootable ISO with the linux version of hponcfg installed so you can boot into that and do what you like.

blocks|key|734933|text|您需要的是Compaq+Light-Outs配置实用程序：|type|unstyled|depth|inlineStyleRanges|entityRanges|data|734934|http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?swItem=MTX-0fcb2f1331034568b60b4061f1&lang=en&cc=us&mode=3&|offset|length|734935|这与HPONCFG的工作原理基本相同，但您可以指定iLO接口地址。如果您想更新批量的iLO接口，那么我已经为此编写了一些powershell脚本。|734936|http://practicaladmin.wordpress.com/2010/11/29/ilo-bulk-updater-v3-0-now-with-less-perl/|734937|希望这能有所帮助|entityMap|0|LINK|mutability|MUTABLE|url|1^0|0|0|3O|0|0|0|0|2G|1|0^^$0|@$1|2|3|4|5|6|7|S|8|@]|9|@]|A|$]]|$1|B|3|C|5|6|7|T|8|@]|9|@$D|U|E|V|1|W]]|A|$]]|$1|F|3|G|5|6|7|X|8|@]|9|@]|A|$]]|$1|H|3|I|5|6|7|Y|8|@]|9|@$D|Z|E|10|1|11]]|A|$]]|$1|J|3|K|5|6|7|12|8|@]|9|@]|A|$]]]|L|$M|$5|N|O|P|A|$Q|C]]|R|$5|N|O|P|A|$Q|I]]]]

What you need is the Compaq Light-Outs config utility:

<a href="http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?swItem=MTX-0fcb2f1331034568b60b4061f1&amp;lang=en&amp;cc=us&amp;mode=3&amp;" rel="nofollow noreferrer">http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?swItem=MTX-0fcb2f1331034568b60b4061f1&amp;lang=en&amp;cc=us&amp;mode=3&amp;</a>

This basically works the same as HPONCFG, except you are able to specify iLO interface addresses. If you are wanting to update batches of iLO interfaces, then I've made some powershell scripts for that.

<a href="http://practicaladmin.wordpress.com/2010/11/29/ilo-bulk-updater-v3-0-now-with-less-perl/" rel="nofollow noreferrer">http://practicaladmin.wordpress.com/2010/11/29/ilo-bulk-updater-v3-0-now-with-less-perl/</a>

Hope this helps

blocks|key|3022053|text|虽然这是一个老问题，但有一个更好的办法。|type|unstyled|depth|inlineStyleRanges|entityRanges|data|3022054|如果您使用了HP版本的EXSi，那么HP驱动程序将自动安装，您应该能够看到硬件选项卡中列出的各种附加硬件。|3022055|您还可以通过VUM分别安装HP驱动程序。|3022056|一旦正确的司机到位，你应该看到基板管理控制器。|3022057|最简单的方法是复制hponcfg文件，编辑该文件并复制回来。|3022058|1)本地或通过SSH连接|3022059|2)复制配置文件|3022060|/opt/hp/tools+#+./hponcfg+-w+ilo.xml
HP+Lights-Out+Online+Configuration+utility
Version+4.0-10+(c)+Hewlett-Packard+Company,+2011
Firmware+Revision+=+1.81+Device+type+=+iLO+2+Driver+name+=+hpilo
Management+Processor+configuration+is+successfully+written+to+file+"ilo.xml"|code-block|syntax|javascript|3022061|3)使用所需参数(登录凭据、IP地址、子网掩码、DNS名称、DHCP启用/禁用和域名)编辑XML|3022062|4)覆盖配置文件|3022063|/opt/hp/tools+#+./hponcfg+-f+ilo.xml
HP+Lights-Out+Online+Configuration+utility
Version+4.0-10+(c)+Hewlett-Packard+Company,+2011
Firmware+Revision+=+1.81+Device+type+=+iLO+2+Driver+name+=+hpilo
<INFORM>Integrated+Lights-Out+will+reset+at+the+end+of+the+script.</INFORM>

Please+wait+while+the+firmware+is+reset.+This+might+take+a+minute++++
Script+succeeded|3022064|以上可能需要超过一分钟，所以不要惊慌！|entityMap^0|0|0|0|0|0|0|0|0|0|0|0^^$0|@$1|2|3|4|5|6|7|11|8|@]|9|@]|A|$]]|$1|B|3|C|5|6|7|12|8|@]|9|@]|A|$]]|$1|D|3|E|5|6|7|13|8|@]|9|@]|A|$]]|$1|F|3|G|5|6|7|14|8|@]|9|@]|A|$]]|$1|H|3|I|5|6|7|15|8|@]|9|@]|A|$]]|$1|J|3|K|5|6|7|16|8|@]|9|@]|A|$]]|$1|L|3|M|5|6|7|17|8|@]|9|@]|A|$]]|$1|N|3|O|5|P|7|18|8|@]|9|@]|A|$Q|R]]|$1|S|3|T|5|6|7|19|8|@]|9|@]|A|$]]|$1|U|3|V|5|6|7|1A|8|@]|9|@]|A|$]]|$1|W|3|X|5|P|7|1B|8|@]|9|@]|A|$Q|R]]|$1|Y|3|Z|5|6|7|1C|8|@]|9|@]|A|$]]]|10|$]]

Although this is an old question, there is a better approach to this.

If you have used the HP version of EXSi, then the HP drivers are automatically installed and you should able to see various additional hardware listed in the Hardware Tab.

You can also install the HP drivers seperately via VUM.

Once correct drivers are in place, you should see Baseboard Management Controller.

Easiest way to do this is copy the hponcfg file, edit that file and copy back.

1) Connect locally or via SSH

2) Copy config file

<pre><code>/opt/hp/tools # ./hponcfg -w ilo.xml
HP Lights-Out Online Configuration utility
Version 4.0-10 (c) Hewlett-Packard Company, 2011
Firmware Revision = 1.81 Device type = iLO 2 Driver name = hpilo
Management Processor configuration is successfully written to file "ilo.xml"
</code></pre>

3) Edit the XML with desired parameters (login credentials, IP address, Subnet Mask, DNS Name, DHCP Enable/Disable &amp; Domain Name)

4) Overwrite config file

<pre><code>/opt/hp/tools # ./hponcfg -f ilo.xml
HP Lights-Out Online Configuration utility
Version 4.0-10 (c) Hewlett-Packard Company, 2011
Firmware Revision = 1.81 Device type = iLO 2 Driver name = hpilo
&lt;INFORM&gt;Integrated Lights-Out will reset at the end of the script.&lt;/INFORM&gt;

Please wait while the firmware is reset. This might take a minute 
Script succeeded
</code></pre>

The above may take more then a minute, so don't panic!

blocks|key|734949|text|您可以使用可用于此目的的Hponcfg脚本。|type|unstyled|depth|inlineStyleRanges|entityRanges|data|entityMap^0^^$0|@$1|2|3|4|5|6|7|C|8|@]|9|@]|A|$]]]|B|$]]

You may use Hponcfg scripts which can be used for this purpose

I was used to configure HP iLO from Windows OS using hponcnfg, but how it can be done when operating system is ESXi 4.1 without phisically connect to the iLO port (aka remotely)?

Thank you all for help

How setup iLO remotely

翻译质量差，导致语言生硬或混乱。

没有提供实际的解决方法或示例。

解答不清晰，无法理解或解决问题。

页面排版不美观，阅读体验差。

文章

问答

视频

教程

学习中心

腾讯云实验室

直播

竞赛

腾讯云代码分析专区

腾讯iOA零信任安全管理系统专区

腾讯云架构师技术同盟交流圈

腾讯云数据库专区

腾讯云智能顾问专区

腾讯云原生专区

腾讯混元专区

腾讯云TCE专区

腾讯云Lighthouse专区

腾讯云HAI专区

腾讯云Edgeone专区

腾讯云存储专区

腾讯云智能专区

腾讯轻联专区 

腾讯云开发专区

TAPD专区

腾讯轻量云游戏服专区

腾讯云最具价值专家

腾讯云架构师技术同盟

腾讯云创作之星

腾讯云开发者先锋

腾讯云AI代码助手

云原生构建

TAPD 敏捷项目管理

Cloud Studio

SDK中心

API中心

命令行工具

功能1上新10个字符

功能2描述100个字符功能2描述100个字符功能2描述100个字符功能2描述100个字符功能2描述100个字符功能2描述100个字符功能2描述100个字符功能2描述100个字符功能2描述100个字符。

功能2上新100个字符功能2上新100个字符功能2上新100个字符功能2上新100个字符功能2上新100个字符功能2上新100个字符功能2上新100个字符功能2上新100个字符功能2上新100个字符。

功能5描述100个字符功能5描述100个字符功能5描述100个字符功能5描述100个字符功能5描述100个字符功能5描述100个字符

功能5上新100个字符功能5上新100个字符功能5上新100个字符功能5上新100个字符功能5上新100个字符功能5上新100个字符功能5上新100个字符功能5上新100个字符功能5上新100个字符功能5上新100个字符

功能4上新

文章&问答评论现已支持表情

全新交互，全新视觉，新增快捷键、悬浮工具栏、高亮块等功能并同时优化现有功能，全面提升创作效率和体验

社区富文本编辑器全新改版！诚邀体验～ 

精选全网热门MCP server，让你的AI更好用 🚀

💥开发者 MCP广场重磅上线！

涵盖代码开发、场景应用、自动测试全流程，助你从零构建专属AI助手

一站式MCP教程库，解锁AI应用新玩法

聚焦“写作效率、视觉美观与运行性能”三方面进行全面升级，为您提供更高效、稳定的创作环境

社区富文本&Markdown编辑器全新改版上线，欢迎大家体验!

诚挚邀请您参与本次调研，分享您的真实使用感受与建议。您的反馈至关重要，感谢您的支持与参与！

社区新版编辑器体验调研

我习惯于使用hponcnfg从Windows配置HP iLO，但是当操作系统是ESXi 4.1时，如何实现它，而不需要连接到iLO端口(也就是远程连接)？谢谢大家的帮助

问如何远程设置iLO
EN

回答 5

Server Fault用户

Server Fault用户

Server Fault用户

社区

活动

圈层

关于

腾讯云开发者

热门产品

热门推荐

更多推荐

问如何远程设置iLOEN

回答 5

Server Fault用户

Server Fault用户

Server Fault用户

社区

活动

圈层

关于

腾讯云开发者

热门产品

热门推荐

更多推荐

问如何远程设置iLO
EN