路由器上的棍子和VRRP在同一路由器和完全冗余可能吗？

Question

棒上的路由器在g0/0.10、g0/0.20和g0/0.30上运行VRRP。

在交换机上，端口fa0/1-8位于VLAN 10上，fa0/23和fa0/24配置为主干端口，允许VLAN 10、20和30。

在HQ2上显示VRRP显示所有VRRP均为主控，而在HQ1上显示为init，路由器运行IOS 15.1，交换机为3560，运行IOS 12.2。

我让路由器在一个棒上运行，一个路由器和一个交换机没有问题，而且VRRP运行在一个没有问题的开关上，但是这里有些东西我不明白！路由器和交换机上没有其他配置。

HQ2上的地址已更改为x.253。配置HQ1

 HQ1>show run
          ^
% Invalid input detected at '^' marker.

HQ1>ena
Current configuration : 1712 bytes  
version 15.4  
hostname HQ1  
ip cef  
redundancy  
interface GigabitEthernet0/0  
 no ip address  
 duplex auto  
 speed auto  
interface GigabitEthernet0/0.10  
 encapsulation dot1Q 10  
 ip address 192.168.222.254 255.255.255.0  
 vrrp 1 ip 192.168.222.100 
interface GigabitEthernet0/0.20  
 encapsulation dot1Q 20  
 ip address 192.168.223.254 255.255.255.0  
 vrrp 2 ip 192.168.223.100  
interface GigabitEthernet0/0.30  
 encapsulation dot1Q 30 native  
 ip address 192.168.224.254 255.255.255.0  
 vrrp 3 ip 192.168.224.100  
interface GigabitEthernet0/1  
 ip address 200.100.0.14 255.255.255.252  
 duplex auto  
 speed auto  
interface Serial0/0/0  
 ip address 10.1.1.1 255.255.255.252  
 clock rate 2000000  

另一个路由器上的配置是相同的，除了g0/0.10 .20和.30的地址终止于253而不是254，当然串行连接的地址也不同。同时也发现交换机上有坏的端口，所以两个VRRP现在都在说主人，所以他们不沟通。

HQ1(config-subif)#do show vrrp  
GigabitEthernet0/0.10 - Group 1  
  State is Backup  
  Virtual IP address is 192.168.222.100  
  Virtual MAC address is 0000.5e00.0101  
  Advertisement interval is 1.000 sec  
  Preemption enabled  
  Priority is 100  
  Master Router is 192.168.222.253, priority is 150  
  Master Advertisement interval is 1.000 sec  
  Master Down interval is 3.609 sec (expires in 3.369 sec)  

GigabitEthernet0/0.20 - Group 2  
  State is Backup  
  Virtual IP address is 192.168.223.100  
  Virtual MAC address is 0000.5e00.0102  
  Advertisement interval is 1.000 sec  
  Preemption enabled  
  Priority is 100  
  Master Router is 192.168.223.253, priority is 150  
  Master Advertisement interval is 1.000 sec  
  Master Down interval is 3.609 sec (expires in 3.153 sec)  

GigabitEthernet0/0.30 - Group 3  
  State is Master  
  Virtual IP address is 192.168.224.100  
  Virtual MAC address is 0000.5e00.0103  
  Advertisement interval is 1.000 sec  
  Preemption enabled  
  Priority is 100  
  Master Router is 192.168.224.254 (local), priority is 100  
  Master Advertisement interval is 1.000 sec  
  Master Down interval is 3.609 sec  

HQ2#show vrrp  
GigabitEthernet0/0.10 - Group 1  
  State is Master  
  Virtual IP address is 192.168.222.100  
  Virtual MAC address is 0000.5e00.0101  
  Advertisement interval is 1.000 sec  
  Preemption enabled  
  Priority is 150  
  Master Router is 192.168.222.253 (local), priority is 150  
  Master Advertisement interval is 1.000 sec  
  Master Down interval is 3.414 sec  

GigabitEthernet0/0.20 - Group 2  
  State is Master  
  Virtual IP address is 192.168.223.100  
  Virtual MAC address is 0000.5e00.0102  
  Advertisement interval is 1.000 sec  
  Preemption enabled  
  Priority is 150  
  Master Router is 192.168.223.253 (local), priority is 150  
  Master Advertisement interval is 1.000 sec  
  Master Down interval is 3.414 sec  

GigabitEthernet0/0.30 - Group 3  
  State is Master  
  Virtual IP address is 192.168.224.100  
  Virtual MAC address is 0000.5e00.0103  
  Advertisement interval is 1.000 sec  
  Preemption enabled  
  Priority is 150  
  Master Router is 192.168.224.253 (local), priority is 150  
  Master Advertisement interval is 1.000 sec  
  Master Down interval is 3.414 sec  

Answer 1

好的，我发现了问题，出于某种原因，删除启动-config并没有真正擦除所有的东西，所以我进入rommon并将HQ2重置为工厂默认值，并且它正在工作。