在H3C S5820X-28S交换机上启用以太网端口

Question

我正在开发一个客户端的H3C S5820X-28S交换机。我完全不熟悉H3C (据我所知，这只是惠普收购前的一个交换机)，它只触及了思科和一些Juniper交换机。

无论如何，我有一个10 but端口，似乎是配置，但拒绝打开的原因。这是在一个远程数据中心和我的眼睛在开关说，我们有正确的修补，但没有得到链接。我已经成功地提取了它当前的配置，这就是它设置的内容：

 [conf]display interface Ten-GigabitEthernet1/0/14
 Ten-GigabitEthernet1/0/14 current state: DOWN
 IP Packet Frame Type: PKTFMT_ETHNT_2, Hardware Address: 3822-d6e5-3763
 Description: Ten-GigabitEthernet1/0/14 Interface
 Loopback is not set
 Media type is stack wire,Port hardware type is STACK_SFP_PLUS
 10Gbps-speed mode, full-duplex mode
 Link speed type is force link, link duplex type is force link
 Flow-control is not enabled
 The Maximum Frame Length is 10000
 Broadcast MAX-ratio: 100%
 Unicast MAX-ratio: 100%
 Multicast MAX-ratio: 100%
 Allow jumbo frame to pass
 PVID: 101
 Link delay is 0(sec)
 Port link-type: access
 Tagged   VLAN ID : none
 Untagged VLAN ID : 101
 Port priority: 0
 Peak value of input: 0 bytes/sec, at 2003-08-06 09:46:13
 Peak value of output: 0 bytes/sec, at 2003-08-06 09:46:13
 Last 300 seconds input:  0 packets/sec 0 bytes/sec 0%
 Last 300 seconds output:  0 packets/sec 0 bytes/sec 0%
 Input (total):  0 packets, 0 bytes
         0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses
 Input (normal):  0 packets, - bytes
         0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses
 Input:  0 input errors, 0 runts, 0 giants, 0 throttles
         0 CRC, 0 frame, - overruns, 0 aborts
         - ignored, - parity errors
 Output (total): 0 packets, 0 bytes
         0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses
 Output (normal): 0 packets, - bytes
         0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses
 Output: 0 output errors, - underruns, - buffer failures
         0 aborts, 0 deferred, 0 collisions, 0 late collisions
         0 lost carrier, - no carrier

我已经用shutdown/undo shutdown手动启用/禁用了端口，但仍然无法工作。在配置中我可能遗漏了什么吗？

Answer 1

Media type is stack wire,Port hardware type is STACK_SFP_PLUS

您还没有说明连接到端口的是什么，或者是否存在任何syslog错误(可能是“不受支持的”SFP)，运行"display transceiver interface“来查看它对该模块(S)的看法。你的输出显示一个直接连接的电缆被插入.

Answer 2

我意识到这是一篇老文章，但事实证明，这个问题是个糟糕的发烧友。订了一个新的，一切都正常了。