UbuntuServer19.04没有在戴尔Poweredge R610上安装以太网固件

Question

我知道这是个棘手的问题，但我需要能够在我的戴尔Poweredge R610上手动安装以太网驱动程序，因为它在默认情况下不会安装任何驱动程序来连接互联网。任何能够做到这一点的帮助都将不胜感激。

结果从命令lspci -nnk | grep 0200 -A3注意:因为我没有SSH或互联网，局域网或广域网。我必须手动输入，它们可能是错误。

01:00.0 Ethernet controller [0200]: Broadcom Inc. and subsidiaries NetXtreme II BCM5709 Gigabit Ethernet [14e4:1639] (rev 20)
    Subsystem: Dell PowerEdge R610 BCM5709 Gigabit Ethernet [1028:0236]
    Kernel driver in use: bnx2
    Kernel modules: bnx2
01:00.1 Ethernet controller [0200]: Broadcom Inc. and subsidiaries NetXtreme II BCM5709 Gigabit Ethernet [14e4:1639] (rev 20)
    Subsystem: Dell PowerEdge R610 BCM5709 Gigabit Ethernet [1028:0236]
    Kernel driver in use: bnx2
    Kernel modules: bnx2
02:00.0 Ethernet controller [0200]: Broadcom Inc. and subsidiaries NetXtreme II BCM5709 Gigabit Ethernet [14e4:1639] (rev 20)
    Subsystem: Dell PowerEdge R610 BCM5709 Gigabit Ethernet [1028:0236]
    Kernel driver in use: bnx2
    Kernel modules: bnx2
02:00.1 Ethernet controller [0200]: Broadcom Inc. and subsidiaries NetXtreme II BCM5709 Gigabit Ethernet [14e4:1639] (rev 20)
    Subsystem: Dell PowerEdge R610 BCM5709 Gigabit Ethernet [1028:0236]
    Kernel driver in use: bnx2
    Kernel modules: bnx2

cat /etc/netplan/*.yaml

# This file is generated from information provided by
# the datasource. Changes to it will not persist across an instance.
# To disable cloud-init's network configuration capabilities, write a file
# /etc/cloud/cloud.cfg.d/99-disable-network-config.cfg with the following:
# network: {config: disabled}
network:
    ethernets: {}
    version: 2

Answer 1

您的netplan文件当前显示：

# This file is generated from information provided by
# the datasource. Changes to it will not persist across an instance.
# To disable cloud-init's network configuration capabilities, write a file
# /etc/cloud/cloud.cfg.d/99-disable-network-config.cfg with the following:
# network: {config: disabled}

我建议你这么做。从航站楼：

sudo -i
echo "network: {config: disabled}"  >>  /etc/cloud/cloud.cfg.d/99-disable-network-config.cfg

接下来，让我们修改netplan文件以添加您的配置：

nano /etc/netplan/50-cloud-init.yaml

按我下面的建议编辑该文件以包括您的设置：

# This file is generated from information provided by
# the datasource. Changes to it will not persist across an instance.
# To disable cloud-init's network configuration capabilities, write a file
# /etc/cloud/cloud.cfg.d/99-disable-network-config.cfg with the following:
# network: {config: disabled}
network:
  version: 2
  renderer: networkd
  ethernets:
    eno1:
      dhcp4: true

Netplan在缩进和间距方面非常具体。请仔细校对两次。保存(Ctrl+o，后面跟着Enter)和退出(Ctrl+x)文本编辑器。下一步：

netplan generate
netplan apply
exit

重新启动。你应该准备好了。

编辑:如果您喜欢服务器推荐的统计IP地址，我建议将您的/etc/netplan/50-cloud-init.yaml文件修改为：

network:
  version: 2
  renderer: networkd
  ethernets:
    enp3s0:
      addresses:
        - 10.10.10.2/24
      gateway4: 10.10.10.1
      nameservers:
          addresses: [10.10.10.1, 8.8.8.8]

当然，用这里来代替你的细节。跟随：

sudo netplan generate
sudo netplan apply

重新启动。

参考:请参阅/usr/share/doc/ netplan /示例中的许多netplan模板。

Answer 2

看起来你已经有了合适的固件。确保你实际上是连接到你的网卡互联网。如果您对服务器具有物理访问权限，只需将其以太网电缆插入到指定设备上，并检查它是否有效。

最后，我们不知道您的网络配置是什么，可能没有DHCP在运行，您需要在四个接口之一上手动设置您的网络配置。它包括IP、网关、网络掩码、广播、路由和DNS服务器等接口配置。

非主题注意:如果提示您在ubuntu安装过程中丢失固件，您应该写下哪些设备缺少固件包。然后，您可以将它们分别作为.deb包下载，并将它们写成f.e。在安装过程中悬挂并指出其位置。