在Cisco 897上配置VDSL？它不会拨号的！

Question

我是新的思科产品，并一直跟随一些在线指南，详细的步骤，要求设置，但被困在一个有点老一套。据我所知，我相信所有正确的接口都配置好了，并配置了一个拨号程序。有人能发现任何明显的错误并帮助一个兄弟吗？提前谢谢你！

我配置的精简版本

ip dhcp excluded-address 10.10.10.1 10.10.10.29
ip dhcp excluded-address 10.10.10.201 10.10.10.254
!
ip dhcp pool Public
 import all
 network 10.10.10.0 255.255.255.0
 dns-server 8.8.8.8 1.1.1.1 
 domain-name techbit.info
 default-router 10.10.10.1 
!

controller VDSL 0
!
!
interface ATM0
 no ip address
 no atm ilmi-keepalive
 pvc 0/38 
  encapsulation aal5mux ppp dialer
  dialer pool-member 1
 !
!
interface Ethernet0
 no ip address
 ip flow ingress
 ip flow egress
 ip virtual-reassembly in
!
interface Vlan1
 ip address 10.10.10.1 255.255.255.0
 ip virtual-reassembly in
!
interface Dialer1
 ip address negotiated
 ip nat outside
 ip virtual-reassembly in
 encapsulation ppp
 dialer pool 1
 dialer-group 1
 ppp authentication chap callin
 ppp chap hostname *******@skydsl
 ppp chap password 0 ********
 ppp pap sent-username ********@skydsl password 0 redacted
 ppp ipcp dns request
 ppp ipcp route default
 no cdp enable
!
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
!
ip route 0.0.0.0 0.0.0.0 Dialer1
!
no logging trap
!
!
!
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
!
mgcp profile default
!
!
!
!
!
line con 0
 no modem enable
line aux 0
line vty 0 4
 privilege level 5
 login local
 transport input telnet ssh
!
scheduler allocate 20000 1000
!
end

VDSL控制器状态(我可以看到我有Showtime，所以在Auth或路由方面肯定有问题？)

Controller VDSL 0 is UP

Daemon Status:       Up 

            XTU-R (DS)      XTU-C (US)
Chip Vendor ID:     'BDCM'           'IFTN'
Chip Vendor Specific:   0x0000           0xD086
Chip Vendor Country:    0xB500           0xB500
Modem Vendor ID:    'CSCO'           '    '
Modem Vendor Specific:  0x4602           0x0000
Modem Vendor Country:   0xB500           0x0000
Serial Number Near:    FGL2023258U C887VAM- 15.3(3)M6
Serial Number Far:     
Modem Version Near:    15.3(3)M6
Modem Version Far:     0xd086

Modem Status:        TC Sync (Showtime!) 
DSL Config Mode:     AUTO 
Trained Mode:        G.993.2 (VDSL2) Profile 17a
TC Mode:         PTM 
Selftest Result:     0x00 
DELT configuration:  disabled 
DELT state:      not running 
Trellis:         ON           ON
SRA:             disabled            disabled
 SRA count:          0           0
Bit swap:        enabled             enabled
 Bit swap count:     0           0
Line Attenuation:     0.0 dB          0.0 dB
Signal Attenuation:   0.0 dB          0.0 dB
Noise Margin:         6.1 dB          6.3 dB
Attainable Rate:    23764 kbits/s        3829 kbits/s
Actual Power:        10.2 dBm         7.2 dBm
Per Band Status:        D1  D2  D3  U0  U1  U2  U3
Line Attenuation(dB):   22.0    67.1    102.3   10.9    54.9    65.3    N/A 
Signal Attenuation(dB): 22.0    67.1    N/A 10.6    54.6    N/A N/A 
Noise Margin(dB):       6.1 6.1 N/A 7.5 6.2 N/A N/A 
Total FECC:     19338            769
Total ES:       8            119
Total SES:      5            0
Total LOSS:     0            0
Total UAS:      60           658
Total LPRS:     0            0
Total LOFS:     5            0
Total LOLS:     0            0

Full inits:     2
Failed full inits:  0
Short inits:        0
Failed short inits: 0

Firmware    Source      File Name (version)
--------    ------      -------------------
VDSL        embedded    VDSL_LINUX_DEV_01212008 (1)

Modem FW  Version:  130205_1433-4.02L.03.A2pv6C035j.d23j
Modem PHY Version:  A2pv6C035j.d23j
Vendor Version:     Ap6v35j.23j 68


          DS Channel1     DS Channel0   US Channel1   US Channel0
Speed (kbps):             0        20698             0          3788
SRA Previous Speed:       0        20682             0          3788
Previous Speed:           0        20682             0          3788
Reed-Solomon EC:          0        17982             0           387
CRC Errors:           0          985             0           183
Header Errors:            0           21             0             0
Interleave (ms):       0.00         8.00          0.00          0.00
Actual INP:        0.00         3.00          0.00          0.00

Training Log :  Stopped
Training Log Filename : flash:vdsllog.bin

界面状态

ATM0 is down, line protocol is down 
  Hardware is MPC/AOE ATMSAR, address is e00e.da57.4088 (bia e00e.da57.4088)
  MTU 1600 bytes, sub MTU 1600, BW 4608 Kbit/sec, DLY 80 usec, 
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ATM, loopback not set
  Keepalive not supported 
  Encapsulation(s): AAL5
  4 maximum active VCs, 1024 VCs per VP, 0 current VCCs
  VC Auto Creation Disabled.
  VC idle disconnect time: 300 seconds
  Last input never, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: Per VC Queueing
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts (0 IP multicasts)
     0 runts, 0 giants, 0 throttles 
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     0 packets output, 0 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 unknown protocol drops
     0 output buffer failures, 0 output buffers swapped out


Dialer1 is up (spoofing), line protocol is up (spoofing)
  Hardware is Unknown
  Internet address will be negotiated using IPCP
  MTU 1500 bytes, BW 56 Kbit/sec, DLY 20000 usec, 
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation PPP, LCP Closed, loopback not set
  Keepalive set (10 sec)
  DTR is pulsed for 1 seconds on reset
  Last input never, output never, output hang never
  Last clearing of "show interface" counters 00:39:39
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes
     0 packets output, 0 bytes


Ethernet0 is up, line protocol is up 
  Hardware is PQII_VDSL_ETHERNET, address is e00e.da57.408c (bia e00e.da57.408c)
  MTU 1500 bytes, BW 3788 Kbit/sec, DLY 2600 usec, 
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input never, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts (0 IP multicasts)
     0 runts, 0 giants, 0 throttles 
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 input packets with dribble condition detected
     0 packets output, 0 bytes, 0 underruns
     0 output errors, 0 collisions, 4 interface resets
     0 unknown protocol drops
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out


Vlan1 is up, line protocol is up 
  Hardware is EtherSVI, address is e00e.da57.4088 (bia e00e.da57.4088)
  Internet address is 10.10.10.1/24
  MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, 
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive not supported 
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:00, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     6261 packets input, 657444 bytes, 0 no buffer
     Received 791 broadcasts (9 IP multicasts)
     0 runts, 0 giants, 0 throttles 
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     3139 packets output, 1065415 bytes, 0 underruns
     0 output errors, 1 interface resets
     3 unknown protocol drops
     0 output buffer failures, 0 output buffers swapped out

有人能帮忙吗？我显然错过了一些很明显的东西！

Answer 1

 Trained Mode:    G.993.2 (VDSL2) Profile 17a
 TC Mode:         PTM

你的DSL不使用自动取款机。如果它应该是ADSL/ATM，那么您需要设置VDSL控制器来显式使用它。自动检测正在寻找VDSL2 2/PTM。

如果PTM是正确的，那么一切都要通过Ethernet0。正如@jonathanjo所指出的，可以有VLAN标记和PPPoE，或者可以像Et0上的DHCP那样简单。(或者它可能需要dot1x，而这是897所不能做到的。)

Answer 2

我并不声称知道您何时必须配置ATM0，以及何时使用ethernet0.101 (如果您知道，请评论！)，但使用VDSL的思科867 has (在英国)的配置如下：

wan mode dsl
controller VDSL 0
!
interface ATM0
 no ip address
 shutdown
 no atm ilmi-keepalive
!
interface Ethernet0
 no ip address
 no cdp enable

interface Ethernet0.101
 encapsulation dot1Q 101
 pppoe-client dial-pool-number 1

interface Dialer1
 ip address negotiated
 ip nat outside
 ip virtual-reassembly in
 encapsulation ppp
 ip tcp adjust-mss 1400
 dialer pool 1
 ppp authentication chap callin
 ppp chap hostname redacted@redacted
 ppp chap password 0 redacted
 ppp ipcp dns request
 no cdp enable