黑丸STM32F411CEU6 -脉宽调制与libopencm3不工作

Question

我试图让PWM与计时器3工作，我已经遵循参考手册，并相信我有一切正确，但我没有得到任何输出。

我的代码在下面，我一定是遗漏了什么

rcc_periph_clock_enable(RCC_GPIOB);
  gpio_mode_setup(GPIOB, GPIO_MODE_OUTPUT, GPIO_PUPD_NONE,
                  GPIO0 | GPIO4 | GPIO5);
  gpio_set_output_options(GPIOB, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ,
                          GPIO0 | GPIO4 | GPIO5);
  gpio_set_af(GPIOB, GPIO_AF2, GPIO0 | GPIO4 | GPIO5);

  rcc_periph_clock_enable(RCC_TIM3);
  timer_set_mode(TIM3, TIM_CR1_CKD_CK_INT, TIM_CR1_CMS_EDGE, TIM_CR1_DIR_UP);
  timer_set_prescaler(TIM3, 50000000 / 125000 - 1);

  timer_enable_preload(TIM3);
  timer_enable_oc_preload(TIM3, TIM_OC1);

  timer_set_period(TIM3, 0xffff);

  timer_enable_oc_output(TIM3, TIM_OC1);
  timer_set_oc_mode(TIM3, TIM_OC1, TIM_OCM_PWM2);
  // timer_set_oc_mode(TIM3, TIM_OC2, TIM_OCM_PWM2);
  // timer_set_oc_mode(TIM3, TIM_OC3, TIM_OCM_PWM2);

  timer_set_oc_value(TIM3, TIM_OC1, 0x7fff);
  timer_enable_update_event(TIM3);
  timer_generate_event(TIM3, TIM_EGR_UG);
  timer_enable_counter(TIM3);

Answer 1

有几件事要记住：

• gpio_mode_setup()应该使用GPIO_MODE_AF，而不是GPIO_MODE_OUTPUT
• some计时器只需要16位计数器，有些是32位计数器.重复检查您的计时器是否为suitable
• different引脚，允许计时器、通道和备用函数号的各种组合。检查数据表以确保使用正确的值

下面是一个在PA0上使用TIM5在stm32f411re上输出频率为400 on，占空比25%的例子：

#include <libopencm3/stm32/rcc.h>
#include <libopencm3/stm32/gpio.h>
#include <libopencm3/stm32/timer.h>
#include <libopencm3/cm3/nvic.h>

// PA0 TIM5_CH1. AF2


const uint32_t timer_peri = TIM5; // timer peripheral
const enum tim_oc_id oc_id = TIM_OC1; // output compare channel designator

int main(void)
{

    // setup PA0 for PWM
    rcc_periph_clock_enable(RCC_GPIOA);
    rcc_periph_clock_enable(RCC_TIM5); // enable TIM clock
    gpio_mode_setup(GPIOA, GPIO_MODE_AF, GPIO_PUPD_NONE, GPIO0); // pin PA11 Alt Function
    gpio_set_af(GPIOA, GPIO_AF2, GPIO0);

    int freq = 400;
    timer_set_prescaler(timer_peri, 16-1); // s/b 1MHz
    int period = 1000000/freq; // assumes prescaled set to 1MHz
    timer_enable_preload(timer_peri); // causes counter to be loaded from its ARR only at next update event
    timer_set_period(timer_peri, period); // set the timer period in the (ARR) auto-reload register
    timer_set_oc_value(timer_peri, oc_id, period * 1/4); // set duty cycle to 25%
    timer_set_counter(timer_peri, 0); // TIM_CNT
    
    timer_enable_oc_preload(timer_peri, oc_id);
    timer_set_oc_mode(timer_peri, oc_id, TIM_OCM_PWM1); // output active when counter is lt compare register
    timer_enable_oc_output(timer_peri, oc_id); // enable timer output compare
    timer_continuous_mode(timer_peri); // enable the timer to run continuously
    timer_generate_event(timer_peri, TIM_EGR_UG); // required!
    timer_enable_counter(timer_peri);
    //timer_enable_irq(timer_peri, TIM_DIER_COMIE);  //enable commutation interrupt
    //nvic_enable_irq(NVIC_TIM1_CC_IRQ);

    while (1);
}

让它适应你的需要。